Phnom Penh, serving Cambodia and the region

Pillar guide

The Industrial Compressed Air Guide

An industrial compressed air system has six parts: generation (compressors), treatment (aftercoolers, dryers and filters), storage and condensate handling, distribution (ring mains and drops), power and control, and the compressor room. A good system delivers the flow the plant actually uses, at the lowest stable pressure, to the ISO 8573-1 purity class each process needs, with minimal unloaded running and leakage. Size it from measured demand, treat air only to the class required, control the compressors as one hall and verify energy against a baseline.

Nexus Turnkey Engineering TeamUpdated 24 min read

What a well-engineered compressed air system does

Compressed air looks free at the point of use. It is not. A compressor turns electricity into pressure, and most of that electricity leaves the compressor as heat. Every m³ that leaks, every bar of excess pressure and every hour a compressor runs unloaded is paid for in kWh.

A well-engineered system does five things:

  1. It delivers the flow the plant actually uses, measured, not guessed.
  2. It holds the lowest stable pressure that keeps every process working.
  3. It treats air to the purity class each process needs under ISO 8573-1, and no further.
  4. It runs the compressors as one hall, with minimal unloaded running and no fights between controllers.
  5. It is visible: flow, pressure, power and dew point are measured, so problems show up as numbers before they show up as scrap or a stopped line.

This guide follows the air from the intake filter to the machine. It covers generation, treatment, storage and condensate, distribution, control and monitoring, energy, maintenance and how to plan a project, whether you are building a new plant or renovating one that is already running. Each section links to deeper articles in our insights library and to the engineering tools you can use with your own numbers.

The equipment is only one part of it. The six packages below have to be designed together, because a decision in one changes the others.

PackageWhat it coversWhat decides the design
GenerationCompressors, fixed speed, VSD or PM-VSD, oil-injected or oil-freeDemand profile, duty and standby, verified delivery
TreatmentAftercoolers, separators, dryers, filtersPressure dew point, particle and oil class, site conditions
Storage and condensateReceivers, drains, oil-water separatorsTransient demand, pressure stability, safe disposal
DistributionRing mains, headers, drops, isolationPressure loss, materials, access, expansion
Power and automationPanels, metering, sequencing, SCADASafe integration, coordinated control, usable data
Compressor roomLayout, ventilation, drainage, accessNo hot-air recirculation, room to maintain

Start with demand, not with a compressor

The most common mistake in compressed air is choosing the compressor first. Compressor size should be the last number you decide, after you know how much air the plant uses, when it uses it and at what pressure.

Measure the demand profile

Demand is not a single number. It is a profile that changes by shift, by product and by day of the week. To size a system properly you need:

  • Average and peak flow, in m³/min or cfm, logged over a representative production period. A week that includes a weekend shows you the off-production demand, which is mostly leakage.
  • Simultaneous demand: which large users run at the same time. Adding up nameplate consumptions overstates demand, because not every machine draws air at once.
  • Pressure at the point of use, measured at the most demanding machines, not only at the compressor discharge.
  • Air quality per use: which processes need dry, oil-free or particle-controlled air, and which only need general plant air.
  • Hours and seasons: shifts per day, days per year, and how ambient conditions change through the hot and monsoon seasons.

A compressed air audit collects these with data loggers on flow, pressure, power and dew point. If you want to know what a good audit delivers, read what a compressed air audit is and what you should get from one. The international reference for this work is ISO 11011, which sets out how to assess the energy efficiency of a compressed air system.

Speak the same units as your supplier

Compressor capacity is quoted as free air delivery (FAD): the volume of air delivered, expressed at the inlet conditions of the compressor. ISO 1217 defines how FAD and package power are measured. That matters because FAD at inlet conditions is not the same as a “normal” volume (Nm³) referred to 0 °C and 1.013 bar, and neither is the same as a volume at line pressure. When two quotations disagree by a few percent, the reference conditions are often the reason. Our unit converter handles flow, pressure and power conversions.

Base load and trim

Once you have the profile, split it into a base load that runs most of the time and a varying portion on top. The base is covered by one or more machines running at or near full load, where they are most efficient. The varying portion is covered by a trim compressor that follows demand. In most modern halls the trim machine is variable speed. Add one machine in reserve (N+1) if your process cannot tolerate the loss of a compressor.

Compressor size is the last number you decide, not the first.

Generation: choosing compressors that match the duty

With demand understood, you can choose technology. For most industrial plants the workhorse is the rotary screw compressor. Reciprocating machines still suit small, intermittent loads and some high-pressure duties. Centrifugal compressors suit very large, steady flows. Scroll compressors suit small oil-free duties.

Oil-injected or oil-free

In an oil-injected screw, oil seals the rotors, cools the air and lubricates the bearings. A separator removes most of it before the air leaves the package, but some oil carries over as aerosol and vapour. Downstream coalescing filters and activated carbon reduce it further.

An oil-free compressor has no oil in the compression chamber. Larger oil-free screw machines use two-stage compression with intercooling, because without oil to absorb heat the discharge temperature would otherwise be too high.

Which is right depends on the oil class your process needs at the point of use, the risk your quality system will accept, and lifecycle cost. Note that oil-free compression does not make the air oil-free by itself: intake air in an industrial area carries hydrocarbons, so filtration still matters. Our article on oil-free vs oil-injected compressors for food, beverage and pharma goes deeper.

Fixed speed, VSD or PM-VSD

Drive and controlHow it matches demandWhere it fits
Fixed speed, load/unloadRuns at full speed, unloads when pressure reaches the upper set-pointSteady base load at or near full capacity
Variable speed (VSD)Changes motor speed to follow demand within its turndown rangeTrim duty, demand that varies across the day
Permanent-magnet VSD (PM-VSD)Variable speed with a permanent-magnet motorTrim or variable duty where part-load efficiency matters

A fixed-speed machine that spends long periods unloaded wastes energy, because unloaded power is far from zero. A VSD machine that runs at full speed all day gains little and adds drive losses. The answer for most halls is a mix: fixed-speed or VSD base machines and one variable-speed trim machine whose turndown range covers the swing in demand. The trade-offs are covered in fixed speed vs VSD vs PM-VSD compressors.

When you compare packages, look at specific power: input power per unit of FAD, at the same pressure, from data measured to ISO 1217. Motor efficiency classes under the IEC system (IE classes) are one part of it. Airend design, cooling and drive losses are the rest.

Redundancy and duty

Decide early what happens when a compressor stops. For a continuous process, N+1 means the plant still meets peak demand with the largest machine out of service. For a single-shift plant with tolerant processes, a smaller reserve or a rental connection may be enough. Write the decision down, because it changes the number of compressors, the receiver volume and the control logic.

We supply compressors from Ingersoll Rand and Sollant as an authorised distributor, across oil-injected and oil-free screw, fixed speed, VSD and PM-VSD. Ask us which series are currently supplied in Cambodia. Browse the air compressors category, or read how to choose the right air compressor for your factory in Cambodia.

The compressor room in tropical heat

Compressors reject almost all of their input energy as heat. In a hot climate the room is part of the machine. When ambient temperatures are high, hot discharge air that recirculates back to the cooling air inlet pushes the compressor towards its temperature limits, and air inlet density falls as temperature rises.

Good rooms share a few features:

  • Cooling air drawn from the coolest, cleanest side of the building, with intake filtration where dust is heavy.
  • Hot air ducted out of the room, not just released into it, with duct losses checked against the fan capability of the package.
  • Enough space around each machine to remove covers, change coolers and lift the airend or motor.
  • Floor drainage and a defined route for condensate.
  • Clean, stable power: voltage dips and harmonics affect drives and controllers, so protection and power quality belong in the design.

The detail is in designing a compressor room for tropical heat.

Treatment: buy the air quality you need, not the best on the page

Atmospheric air entering a compressor carries water vapour, dust and hydrocarbons. Compression concentrates them. Treatment removes them to the level each process needs. Treating every m³ to the highest class wastes capital and energy, because every dryer and filter adds pressure drop and, in some designs, purge air.

ISO 8573-1 in one page

ISO 8573-1 defines purity classes for three contaminants: particles, water and total oil. A specification is written as three numbers, for example ISO 8573-1:2010 [1:4:2]: particle class 1, water class 4, oil class 2. A lower number is cleaner. Class 0 means a limit set by the user or supplier that is more stringent than class 1, and it must always be stated explicitly. “Class 0” on its own means nothing.

The summary below follows the published class limits of ISO 8573-1:2010. Particle counts are per m³ at the standard’s reference conditions.

ClassParticles, 0.5–1 µmParticles, 1–5 µmWater (pressure dew point)Total oil
1≤ 400≤ 10≤ -70 °C≤ 0.01 mg/m³
2≤ 6,000≤ 100≤ -40 °C≤ 0.1 mg/m³
3≤ 90,000≤ 1,000≤ -20 °C≤ 1 mg/m³
4not specified≤ 10,000≤ +3 °C≤ 5 mg/m³
5not specified≤ 100,000≤ +7 °Cno class
6by mass, ≤ 5 mg/m³by mass, ≤ 5 mg/m³≤ +10 °Cno class

Typical choices look like this. General plant air for tools and machinery is often specified at water class 4, with moderate particle and oil classes. Air that touches food packaging or the product, or that blows onto electronic assemblies, is usually specified tighter on oil and particles. Air for instruments in cold or air-conditioned areas needs a lower dew point so that nothing condenses in the lines. Your quality team, your customer’s code of practice and the equipment manufacturer’s requirements should set the class, not the brochure.

Aftercooling and separation

Air leaves the compression element hot and saturated. An aftercooler cools it, and much of the water vapour condenses. A moisture separator and drain remove that liquid before it reaches the dryer. Most packaged screw compressors include an aftercooler. In a hot climate, the cooling air temperature limits how far it can cool the compressed air, which puts more load on the dryer.

Dryers

Drying is about pressure dew point: the temperature at which water vapour in the compressed air would begin to condense, at line pressure. If no pipe, valve or product surface ever falls below that temperature, no liquid water forms.

Dryer typeTypical pressure dew pointISO 8573-1 water classNotes
Refrigeratedabout +3 to +7 °C4 or 5Low running cost, most general plant air
Desiccant, heatless-40 °C or -70 °C2 or 1Uses a share of dried air as purge
Desiccant, heated or blower-purge-40 °C or -70 °C2 or 1Lower purge loss, more equipment
Membranedepends on designvariesSmall flows, points of use

A useful sense check: a pressure dew point of +3 °C at about 7 bar corresponds to an atmospheric dew point of roughly -20 °C, because expanding the air spreads the same water over a larger volume. That is why a refrigerated dryer is sufficient for most indoor plant air even in a humid climate, as long as the air stays at pressure and the pipes stay warmer than +3 °C.

Dryers are rated at reference inlet temperature, ambient temperature and pressure. In a tropical compressor room the inlet and ambient temperatures are often higher than the rating conditions, so the real capacity is lower. Always apply the manufacturer’s correction factors to your design conditions. Our article on refrigerated vs desiccant dryers and ISO 8573-1 classes shows how to choose.

Filters

Filters do three jobs:

  • Particulate filters remove solid particles, including desiccant dust after a desiccant dryer.
  • Coalescing filters remove oil and water aerosols by making fine droplets merge and drain away.
  • Activated carbon filters adsorb oil vapour and odours, and are the last stage where a low oil class is required.

Filter elements load up over time, and their pressure drop rises. A differential pressure gauge or sensor across each filter tells you when to change elements on condition, not by guesswork. See the air treatment range for dryers, filters, aftercoolers, drains and receivers.

Air that feeds a nitrogen generator

If you generate nitrogen on site, the feed air is part of the treatment design. PSA and membrane generators depend on clean, dry, oil-free feed air, and the generator’s rated output assumes it. Treatment for a nitrogen generator is specified with the generator, not added later. The nitrogen generators in the Nexus range are selected to your purity and flow. Capacities selected to your load. Ask for a datasheet. For the economics, read on-site nitrogen generation vs cylinders.

Storage and condensate: the parts that get under-bought

Receivers

An air receiver does three jobs. It stores air to cover short peaks that would otherwise start another compressor. It damps pressure fluctuations so the control system can hold a narrow band. And it gives the compressors’ control logic time to act, which reduces start-stop and load-unload cycling.

There are usually two locations to consider:

  • A wet receiver before the dryer, which also helps separate liquid water.
  • A dry receiver after the treatment, close to demand, which feeds peaks with air that is already treated.

A common way to estimate storage for a known peak is the receiver formula used in the US DOE and Compressed Air Challenge sourcebook:

V = t × C × pₐ ÷ (p₁ - p₂)

where V is receiver volume, t is the duration of the event the receiver must cover, C is the air demand during that event in excess of compressor supply (as free air), pₐ is atmospheric pressure in absolute units, and p₁ - p₂ is the pressure drop you can accept during the event. Use consistent units: minutes, m³/min and bar give m³. The formula shows why a wider acceptable pressure band reduces the volume needed, and why storage cannot help if the pressure band is too tight to use it.

Receivers are pressure vessels. Specify them to a recognised pressure vessel code, with a correctly set safety valve, a pressure gauge, a drain and an inspection opening, and follow the inspection requirements that apply on your site.

Condensate

Every system makes water. The quantity is larger than most people expect, especially in a hot, humid climate. As an illustration of the physics: a compressor delivering 10 m³/min of free air drawn in at 35 °C and 80% relative humidity, compressed to about 7 bar and dried by a refrigerated dryer to a +3 °C pressure dew point, removes roughly 18 litres of water an hour. Over a 24-hour day that is several hundred litres, from one compressor.

That water must leave the system reliably:

  • Drains at the aftercooler separator, receivers, dryers, filters and low points of the network. A zero-loss drain senses the liquid level and opens only when there is condensate to discharge, so it does not waste compressed air the way a timer drain set to open too long does.
  • Oil-water separators for condensate from oil-injected compressors. This condensate contains lubricant and must not be discharged untreated. Check the discharge limits that apply to your site with your environmental authority or permit.

Distribution: get pressure to the machine without losing it

The pipe network is where good generation and treatment are often undone. Pressure lost in the pipes has to be made up at the compressor, every hour of every day.

Ring mains, headers and drops

A ring main feeds each point from two directions, so the air has two paths and the pressure loss to the furthest user is lower than in a long dead-end line. Good practice includes:

  • Size for velocity and pressure loss, not for the compressor outlet size. Undersized pipes are a permanent energy cost.
  • Slopes and drain legs on wet sections, so any liquid water runs to a drain point rather than to the machine.
  • Drops taken from the top of the header, so liquid in the main does not fall into the branch.
  • Isolation valves that let you work on one section without shutting down the plant.
  • Supports and expansion allowance suitable for the material and the temperature range.
  • Pipe materials suited to the air quality: corrosion inside galvanised steel can add particles downstream of the dryer, which is why aluminium and stainless systems are common in new installations.

How much pressure loss is acceptable? Natural Resources Canada and earlier US DOE / Compressed Air Challenge guidance state that a properly designed system should lose much less than 10% of the compressor’s discharge pressure between the compressor and the point of use. Lower is better: every bar you do not lose in pipes is a bar you do not have to generate.

Pressure loss is a design variable

Look at the whole route from the compressor to the most demanding machine: dryer, filters, header, drop, hose, regulator and coupling. The biggest single losses often sit in the last few metres, in an undersized hose or a quick coupling. The first response to a low-pressure complaint at a machine should be to measure the losses along that route, not to raise the compressor set-point.

Fix the restriction before you raise the set-point.

Expansion and future users

Plan headers and the compressor room for the expansion you expect. A ring main with capped connections and a compressor room with a spare plinth and spare panel capacity cost little at the design stage. Retrofitting them later costs a shutdown.

Control and monitoring: run the hall as one machine

Why controllers fight

Most halls with more than one compressor were built in stages. Each compressor has its own pressure switch or controller, set to cascade bands so that one loads before the next. With three or four machines, the cascade forces the average pressure higher than it needs to be, and several machines can sit part-loaded or unloaded at the same time.

A sequencer or central controller replaces the cascade with one pressure band for the hall. It selects which machines run, keeps the most efficient combination online, rotates duty to equalise running hours, and lets one variable-speed trim machine absorb the swings. The manufacturer’s own machine controllers and protections stay in place at each compressor. The central controller decides what each machine should do; each machine still protects itself.

Monitoring that answers questions

Instruments only matter if they answer an operating question. The ones that do:

MeasurementWhereWhat it tells you
FlowAfter treatment, per major branchDemand, leakage, cost allocation
PressureDischarge, after treatment, far end of networkTreatment and pipe losses
PowerEach compressor and dryerLoaded and unloaded energy
Pressure dew pointAfter each dryerWhether drying works
Filter differential pressureAcross each filterWhen to change elements

With flow and power measured, you can calculate the hall’s specific energy in kWh per m³. That is the number that tells you whether changes worked.

Nexus AirSight brings these signals onto one screen through a PLC and SCADA layer: real-time values, trends, alarms and reports, across compressors from different manufacturers and of different ages. It is an overlay, not a replacement for each compressor’s own logic.

Energy: where the kWh go and how to get them back

Over a compressor’s life, the electricity it uses usually costs more than the machine itself. That makes energy a design variable, not an option to add later.

The main levers

1. Right-size the hall. Match base, trim and reserve capacity to the measured profile. Oversized fixed-speed machines spend their lives unloaded.

2. Coordinate the fleet. One pressure band and one sequencer instead of cascaded set-points. Fewer machines part-loaded at once.

3. Use variable speed selectively. One well-sized variable-speed trim machine usually covers the swing. Several variable-speed machines competing for the same swing do not add efficiency.

4. Lower the pressure. The US Department of Energy and Natural Resources Canada give a rule of thumb for systems around 100 psig (about 7 bar): every 2 psi (about 0.14 bar) of extra discharge pressure raises energy use by roughly 1% at full output flow. Higher pressure also increases the flow lost through leaks and unregulated users. Our pressure reduction savings tool applies this rule of thumb to your figures.

5. Reduce wasted demand. Leaks, open blowing, air used where a blower or electric tool would do the job at lower cost, and machines left pressurised when idle.

6. Recover heat. The Compressed Air Challenge’s heat recovery fact sheet, produced with the US Department of Energy, states that 80 to 93% of the electrical energy used by an industrial air compressor is converted into heat, and that a properly designed heat recovery unit can recover roughly 50 to 90% of that thermal energy. Uses include process hot water, boiler feed preheating and washing. Read heat recovery from air compressors.

80 to 93%Share of a compressor's electrical input converted into heat, according to the Compressed Air Challenge / US DOE heat recovery fact sheet.

Leaks deserve their own programme

The US Department of Energy’s leak tip sheet states that leaks can waste 20 to 30% of a compressor’s output in plants that have not managed them. Leaks also lower system pressure, which pushes operators to raise the set-point, which in turn increases leakage. The fix is a programme, not a one-off: an ultrasonic leak detection survey, tagging, repair, re-survey, and isolation of idle sections out of hours. Our leak detection service follows that cycle, and the leak cost calculator estimates the cost from the DOE orifice method. The background is in compressed air leaks: finding and fixing a hidden cost.

What we promise, and what we don’t

Savings are project-specific. We measure them against a baseline and verify them after implementation; we don’t promise a blanket percentage.

To estimate your current running cost before you start, use the compressed air cost calculator. It splits annual energy into loaded and unloaded running from motor power, load profile and tariff.

The KPIs worth tracking

  • Hall input power and energy (kW, kWh).
  • Delivered volume (m³) and specific energy (kWh/m³).
  • Pressure loss from discharge to the far end of the network.
  • Unloaded running hours and unloaded energy.
  • Pressure dew point after each dryer.
  • Off-production demand, which is mostly leakage.

Maintenance that protects air quality and uptime

Maintenance on compressed air is about three outcomes: the compressors keep running, the air stays in class, and the energy performance does not drift. Follow the manufacturer’s service intervals, adjusted for your operating hours, dust load and ambient temperature.

EquipmentTypical checksWhy it matters
CompressorsIntake filters, oil and oil filters, separator element, cooler cleanliness, belts or couplings, temperaturesOverheating and high separator loss in hot, dusty rooms
DryersCondenser cleanliness, dew point, drain operation, refrigerant circuit or desiccant conditionWater carry-over when dew point drifts
FiltersDifferential pressure, element change on condition or schedulePressure loss and oil or particle breakthrough
Drains and separatorsFunction test, cleaning, oil-water separator mediaFlooding, dirty discharge
NetworkLeak survey, isolation valves, drop conditionWasted flow and pressure
InstrumentsSensor checks and calibrationDecisions are only as good as the data

In a tropical plant, dust on coolers and dryer condensers is one of the most common causes of high temperature trips and poor drying. Cleaning them is cheap. Ignoring them is not.

Planned maintenance, parts and contracts

An annual maintenance contract (AMC) turns this list into a schedule, with genuine parts, trained technicians and a record of every visit. A good contract also includes periodic reviews of operating data, so energy and air-quality drift are caught early. Read what a good compressor maintenance contract should include, see our maintenance contracts, and find service kits, filters, separators and lubricants under spare parts and the spare parts service.

Weekly walk-round

  • Pressure at the far end of the network within the target band
  • Pressure dew point after each dryer within its alarm limit
  • Every drain discharging, no water at low points
  • Filter differential pressures below change limits
  • Compressor room temperature close to outdoor, no hot-air recirculation
  • No new audible leaks; tag any you find
  • Unloaded running hours compared with last week

Planning a project: greenfield and brownfield

Greenfield: size for today, plan for tomorrow

A new plant gives you the chance to get the fundamentals right once: room location and ventilation, pipe routes, storage, metering and control architecture. The risk is guessing demand from nameplates and oversizing. Use the process design and similar operations to build a demand estimate, then size the first phase to it with clear space and connections for the next.

Brownfield: upgrade a live plant

Most projects are in plants that are already running. The work has to happen around production. A typical renovation sequence:

  1. Baseline the condition and energy performance: flow, pressure, power, dew point and leaks.
  2. Decide keep or replace for each machine and component, with a simple matrix: condition, efficiency, parts availability, role in the new system.
  3. Plan the changeover for a live plant: temporary air, weekend cut-overs, and phased ring-main replacement.
  4. Re-pipe from dead ends to loops, with slopes, drains and isolation.
  5. Upgrade treatment to the ISO 8573-1 class actually needed, point by point.
  6. Add a control overlay so old and new machines sequence as one hall.
  7. Hand over properly: P&ID, set-points, spares list and operator instruction.

Machines with useful life left often stay on as peak or standby capacity under the new controls. Our plant renovation page explains how we stage this.

What we often findHow we respond
Overheating and hot-air recirculation in the roomDucted exhaust, separated intake, cooler cleaning
Water at the point of useDrain repair, dryer correction to real conditions, pipe slopes
Low pressure at machinesMeasure losses, fix restrictions and drops before raising pressure
Several compressors part-loaded at onceSequencer, one pressure band, right-sized trim
Old equipment with no visibilityMetering and a monitoring overlay
No room to expandLayout redesign, staged replacement

The delivery sequence

Whether greenfield or brownfield, the work follows the same stages, with documents at each one you can review:

  1. Assess and define: survey, demand and pressure profile, leak survey, required ISO 8573-1 classes, inventory, constraints and expansion.
  2. Evaluate and select: technology options, capacity and N+1, energy and lifecycle cost comparison, preliminary layout and scope.
  3. Engineer and approve: P&IDs, sizing and isometrics, general arrangement, ventilation and condensate design, electrical single-line diagram, bill of materials, control philosophy.
  4. Supply and install: procurement, delivery, mechanical, piping, electrical and instrumentation work, with inspection records.
  5. Integrate and test: controllers, PLC and SCADA, meters and dew-point instruments, logic and alarm tests, staged start-up.
  6. Commission and hand over: SAT and performance checks, air-quality verification, punch list, training, as-built drawings, manuals, spares list and the maintenance plan.

See design and engineering, installation and commissioning and how we work for the detail of each stage.

Before you ask for quotations

  • Measured demand profile, or a plan to measure it
  • Required ISO 8573-1 class for each use, agreed with quality
  • Pressure needed at the most demanding machine
  • Redundancy decision: N+1 or not, and why
  • Compressor room location, ventilation route and drainage
  • Electrical supply capacity and power quality
  • Expansion plans for the next phase
  • Metering and monitoring you want from day one

Where to go next

Compressed air connects to almost every other utility in a plant. If you are working on one part of the system, these pages go deeper:

If you would rather start from data, a measured audit is the fastest way to see where your system stands. Book an air audit or request a quote.

Nexus Turnkey Engineering Team

Written and reviewed by the engineers who design, install and maintain industrial air systems for Nexus Turnkey in Cambodia. Questions about this guide? Ask us directly.

FAQ

Questions engineers ask us

How do I size an air compressor for my plant?

Size from measured demand, not from the sum of nameplate consumptions. Log flow and pressure for at least a representative production week, identify the base load and the peaks, and allow for leakage you intend to fix. Then select a base-load machine and a trim machine (often variable speed) so the fleet covers peak demand with one unit in reserve if your process cannot tolerate a stoppage.

What pressure should a compressed air system run at?

The lowest pressure that keeps the most demanding end use working reliably, plus the pressure losses of the treatment and distribution between them. Fix restrictions such as undersized pipes or blocked filters before raising the set-point. The US Department of Energy gives a rule of thumb that, around 100 psig, every 2 psi of extra discharge pressure raises energy use by about 1% at full output flow.

Do I need a refrigerated dryer or a desiccant dryer?

It depends on the pressure dew point your process needs. A refrigerated dryer typically delivers a pressure dew point in the region of +3 to +7 °C, which matches ISO 8573-1 water class 4 or 5 and suits most general plant air. Desiccant dryers reach -40 °C (class 2) or -70 °C (class 1) and are used where pipes run through cold areas or the product is moisture-sensitive.

Is an oil-free compressor necessary for food or pharmaceutical production?

Not automatically. What matters is the oil class at the point of use, defined by ISO 8573-1. Oil-free compressors remove the risk of lubricant entering the air, which many food, beverage and pharmaceutical quality systems prefer. Oil-injected compressors with suitable coalescing and activated carbon filtration can meet strict oil classes, but the result depends on correct filtration, maintenance and verification.

How much do compressed air leaks cost?

According to the US Department of Energy, leaks can waste 20 to 30% of a compressor's output in a poorly maintained system. The cost on your site depends on the leak flow, the hours and your electricity tariff. Our leak cost calculator uses the DOE method so you can estimate it with your own numbers, and an ultrasonic survey gives the measured figure.

What is a good specific power for a compressed air system?

Specific power (kW per m³/min, or kWh per m³ delivered) depends on pressure, compressor type, size and loading, so there is no single target. Compare packages using manufacturers' data measured to ISO 1217 at the same pressure, then measure the whole system, including dryers and unloaded running, to establish your baseline.

Can you upgrade a compressed air system without stopping production?

Usually, yes. Live-plant upgrades use temporary air, staged cut-overs during planned shutdowns or weekends, and phased ring-main replacement. Existing machines with useful life often stay on as standby or peak capacity under a new control overlay.

Next step

Start with a measured baseline

We log your flow, pressure, power and dew point, then show you where the kWh and the air quality problems actually are.

Start typing to search