Phnom Penh, serving Cambodia and the region

Industry

Air that holds its class on the day of the audit, and every day after

Clean air for pharmaceutical manufacturing means four things that can each be measured: compressed air to a stated ISO 8573-1 class, cleanroom air to an ISO 14644-1 class, controlled humidity and temperature, and a pressure cascade that keeps contamination moving the right way. Nexus Turnkey designs, installs and supports those utilities for pharmaceutical plants, hospitals and laboratories, and hands over the documentation your quality team needs to qualify them. We work to GMP expectations; we don't certify your facility.

Stainless steel process machinery in a modern manufacturing facility
Factory cross-section highlighting the air services used in Pharmaceutical & healthcare: Compressed air, Air treatment, Nitrogen, Dehumidification, Cleanroom, HVAC & chillers, Monitoring (AirSight). PRODUCTION HALLN₂+
Fig. · Factory cross-section, air services

Pharmaceutical & healthcare

Clean air for pharmaceutical manufacturing

Pharmaceutical and healthcare air is judged by numbers: particle counts, pressure differentials, dew points and humidity. The lens shows dry, oil-controlled compressed air and nitrogen for process and packing, HEPA-filtered air handling with a pressure cascade, low-humidity rooms for sensitive products, and the monitoring that records it all.

Air services in focus: Compressed air, Air treatment, Nitrogen, Dehumidification, Cleanroom, HVAC & chillers, Monitoring (AirSight).

Explore pharmaceutical & healthcare

The challenge: every number is a specification

Pharmaceutical manufacturing, hospitals and laboratories all depend on air that meets a stated class and keeps meeting it. Cleanrooms are classified by particle count. Pressure differentials keep contamination flowing from clean to less clean. Humidity and temperature limits protect hygroscopic products and staff comfort in gowns. Compressed air that touches product or primary packaging must be dry, oil-controlled and free of viable organisms.

In Cambodia the climate makes each of these harder. Outdoor air is hot and humid for most of the year. Air handling units therefore carry a large latent load, and cooling coils alone may not hold low humidity in critical rooms. Compressor rooms run hot. Power interruptions can drop air handling units and collapse a pressure cascade within seconds. A design that works on paper in a temperate climate can fail its first humid season.

The second challenge is evidence. A room that met its class at handover but drifted since is a finding waiting to happen. Monitoring, maintenance and records are as much a part of the system as the hardware.

The air services pharma and healthcare need

Cleanroom air and the pressure cascade

The core is the air handling: an AHU with staged pre-filters, cooling and reheat, then terminal HEPA filters in the room. We size airflow to the ISO 14644 class and the heat and particle load. The positive-pressure cascade is set door by door, laminar flow units go over critical operations, and pass boxes move materials without breaking the cascade. Read clean rooms and positive pressure basics and see air quality and emissions.

Humidity and temperature

Low-humidity rooms for powders, capsules and effervescent products often need a desiccant rotor dehumidifier alongside the cooling coil, because a coil can only dry air to near its own surface temperature. We size the latent load from the tropical design condition, not an average day. See dehumidifiers, humidity control and our article on humidity control in pharmaceutical and food production.

Compressed air to a written class

Tablet coating, fluid-bed processing, blister packing and vial handling use compressed air. Each use point gets an ISO 8573-1 class from your risk assessment. To meet it, we specify oil-free or properly filtered generation, a desiccant dryer where a low pressure dew point is needed, and sterile-grade point-of-use filters. Distribution pipework is chosen to stay clean. See compressed air systems and air treatment.

Nitrogen

Nitrogen blankets solvents and sensitive liquids, inerts reactors and flushes packs. A PSA generator delivers the purity you specify, with an analyser and alarm. See nitrogen generators.

Cooling and monitoring

Chillers carry the HVAC and process loads, with N+1 where a room cannot be allowed to drift. A monitoring system records differential pressure, temperature, humidity, particle counts and compressed-air dew point, with alarms and history. See SCADA and monitoring.

Power and resilience

Air handling for graded rooms should restart in a defined sequence after a power cut, so the cascade is re-established before doors open. Standby chillers, backed-up power for monitoring and controls, and alarm logic that tells a door opening from a fan failure are design decisions, not afterthoughts. We write them into the control philosophy and test them at site acceptance.

A cleanroom is only as good as its worst humid afternoon and its last power cut.

Standards that apply

For compressed air, ISO 8573-1:2010 sets the purity classes and ISO 8573-7 the method for testing viable micro-organisms. HEPA filters are classified under EN 1822 and ISO 29463. The filters that protect them are classified under ISO 16890, which replaced EN 779.

Typical scope

PackageWhat it usually includes
User requirementsRoom list, classes, cascade, humidity and temperature limits, air use points
Air handlingAHUs, staged filtration, HEPA terminals, laminar flow units, pass boxes
ClimateCooling, reheat, desiccant dehumidification, chillers with standby
Compressed air and nitrogenGeneration, dryers, sterile filtration, PSA nitrogen
MonitoringDifferential pressure, temperature, humidity, particle and dew-point alarms
HandoverFAT and SAT records, test results, as-builts, maintenance plan

Our design and engineering team writes the specification with you. Installation and commissioning delivers the SAT records and documents your qualification needs. A maintenance contract keeps filter changes, calibrations and records on schedule.

Scope

Relevant standards

Standards that commonly shape this industry's air
StandardWhy it matters here
ISO 14644-1:2015Classifies cleanroom air cleanliness by particle concentration, from ISO Class 1 to 9. The basis for room classes and requalification.
ISO 8573-1:2010Purity classes for compressed air. Product-contact air is specified with a tight oil and water class and tested at the point of use.
GMP guidance (EU GMP Annex 1, WHO, PIC/S)Context, not certification: sets expectations for cleanroom grades, pressure cascades and airflow. Your regulator and quality system decide which applies.
EN 1822 / ISO 29463Classify HEPA filters by efficiency at the most penetrating particle size, for example H13 and H14.
ISO 16890Classifies the pre- and intermediate filters that protect HEPA filters in air handling units.
We design to the standard your process requires. Nexus describes these standards; it does not claim certification against them.

FAQ

Questions engineers ask us

What ISO 8573-1 class does pharmaceutical compressed air need?

There is no single class written into GMP. Your risk assessment sets it by use: air that contacts product or primary packaging usually gets a tight oil class (Class 1, or a specified Class 0), a low pressure dew point and point-of-use sterile filtration, with microbiological testing under ISO 8573-7. We help you write the specification and then design to it.

Can you build a cleanroom to ISO 14644-1?

We design and install the air side: air handling units, HEPA terminal filters, laminar flow units, pass boxes, pressure cascade and monitoring, sized to the class you need. Classification is confirmed by particle-count testing to ISO 14644-1 at handover, by an independent tester if your quality system requires it.

What pressure difference should there be between cleanrooms?

EU GMP Annex 1 gives a guidance value of 10 to 15 Pa between adjacent rooms of different grades. The design sets the cascade direction and value for each door, and differential-pressure sensors with alarms show it is held.

Why does humidity matter for tablets and capsules?

Many powders, effervescent products and gelatin capsules are hygroscopic. They take on moisture, stick to tooling, change weight or lose stability. Rooms that hold a low, steady relative humidity, often with desiccant-rotor dehumidifiers, protect the product and the process. The target comes from your product data.

Do you supply medical air systems for hospitals?

Medical gas pipeline systems are governed by their own standard, ISO 7396-1, and national rules. We focus on the air conditioning, cleanroom and isolation-room air, dehumidification, laboratory ventilation and utility compressed air. Ask us about medical air early so the scope is clear.

What documents do we get for qualification?

Design specifications, P&IDs, equipment datasheets, material and filter certificates from the manufacturers, FAT and SAT records, calibration records for instruments, test results and as-built drawings. They support your IQ and OQ protocols. Qualification and release stay with your quality team.

Next step

Specify your clean air before the room is built

Share your room list, grades and products. We will propose the air handling, cascade, compressed-air class and monitoring to match.

Start typing to search