Toolkit
The engineering toolkit.
Free calculators and references for plant engineers: estimate what leaks and pressure cost, convert units, read ISO 8573-1 classes and find the right kind of system. Every tool shows its formula and the public source it relies on, and every result can be shared or carried into a quote.
- 01Leak cost calculatorA compressed air leak cost calculator turns a count of leaks into air lost, power, energy and annual cost. This one uses the US Department of Energy method: number of leaks × leakage rate (cfm) × kW per cfm × hours × tariff. Leakage rates come from the DOE leak tip sheet table for 1/32 to 3/8 in holes at 70–125 psig, interpolated for your pressure and corrected for orifice shape. The tariff starts at EDC's published industrial rate at medium voltage (USD 0.137/kWh); replace it with your own and, if you have it, your measured specific power. Cost results include a 10 % service fee. The result is an estimate, not a survey: an ultrasonic leak survey measures what you actually have.Explore
- 02Compressed air costA compressed air cost calculator estimates a compressor's annual electricity use and cost from its motor rating, motor efficiency, hours, and the share of time it runs loaded and unloaded. This one uses the part-load equation in the US DOE / Compressed Air Challenge sourcebook: input power = motor rating ÷ efficiency, and annual kWh = input power × hours × (loaded share + unloaded power share × unloaded share). It splits energy into loaded and unloaded running, and, if you enter free air delivery, adds specific power and the real energy per cubic metre. The tariff starts at EDC's published industrial rate at medium voltage (USD 0.137/kWh) and can be replaced with your own; cost results include a 10 % service fee. The result is an estimate, and logged power data is better.Explore
- 03Pressure reduction savingsA pressure reduction savings calculator estimates the energy saved by lowering a compressed air system's set pressure. This one applies the US DOE / Compressed Air Challenge rule of thumb: for systems in the 100 psig range, each 2 psi of discharge pressure changes compressor energy by approximately 1 % at full output flow. Enter current and target pressure in bar or psi, your annual compressor energy and your tariff (it starts at EDC's published industrial rate at medium voltage, USD 0.137/kWh; cost results include a 10 % service fee). An optional term adds the sourcebook's extra 0.6–1.0 % per 2 psi where 30–50 % of demand is unregulated. It is a rule of thumb, not a measurement: your compressor's curves and a pressure survey decide what is achievable.Explore
- 04Unit converterThis compressed air unit converter converts flow (cfm, m³/min, m³/h, L/s), pressure (bar, psi, kPa, MPa, gauge and absolute), power (kW, hp) and temperature (°C, °F, K) using factors derived from exact definitions listed by NIST. 100 cfm is 2.8317 m³/min, 1 bar is 14.504 psi and 1 hp is 0.7457 kW. It changes units only: free air delivery, normal cubic metres and ISO 8573-1 reference volumes are measured at different conditions, and gauge pressure differs from absolute by the atmosphere. Notes on each, and on pressure dew point, sit beside the converter.Explore
- 05ISO 8573-1 class explorerISO 8573-1:2010 specifies compressed air purity as three classes, written particles:water:oil, for example ISO 8573-1:2010 [2:4:2]. Particle classes 1–5 cap particle counts per cubic metre in three size bands; water classes 1–6 cap the pressure dew point (class 4 is +3 °C or lower); oil classes 1–4 cap total oil, including vapour, from 0.01 to 5 mg/m³. Class 0 is a limit agreed between user and supplier that is stricter than class 1, not zero contamination. This explorer lets you pick each class, shows the notation in plain English and the treatment typically needed, as a direction to confirm with your process owner.Explore
- 06System selectorThe Nexus Turnkey system selector is a five-question guide for industrial air projects: what you need air for, your industry, the scale of the job, how clean or dry the air must be, and what matters most. It suggests product directions (such as air compressors, air treatment, dehumidifiers or blowers) and services (such as an air audit or design and engineering), each with a one-line reason, and links to the detail. It never names a model, a size or a saving, because those follow from measuring or agreeing the demand. When you are done, it carries your answers into a quote request.Explore
Next step
Estimates are a start. Measurements decide.
An air audit replaces assumptions with logged data from your own plant.