The problem: emissions are a process problem, not a chimney problem
Most air quality complaints arrive as a symptom. A neighbour smells solvent. Dust settles on the roof. Workers in the coating line complain of headaches. A customer audit asks for emissions data that nobody has. The first instinct is often to buy a filter or a scrubber and fit it to the stack.
That rarely works on its own. Treatment equipment is selected for a particular stream: its airflow, temperature, humidity, the pollutant and its concentration, and how all of these change across a shift. Fit the wrong technology and it either fails to treat the load or costs far more to run than it should. Undersize the capture hoods and the pollutant never reaches the treatment at all. It escapes into the workspace instead.
Industries in Cambodia meet this in different forms. Printing and coating lines emit solvent VOCs. Cement, rice and feed mills generate dust. Chemical processes release acid gases and odours. Pharmaceutical and electronics areas need the opposite problem solved: keeping particles out.
Our approach: characterise, capture, treat, monitor
1. Characterise the stream. We start by understanding what leaves the process. We look at the sources, the airflow at each, temperature and humidity, the pollutant species, their concentration and how it varies over time, and any particulate that would foul downstream media. Where specialist stack sampling is needed, we plan it rather than assume.
2. Capture at the source. The cheapest air to treat is air you never had to move. We design hoods, enclosures and ducting to capture emissions close to where they are released. That keeps the total airflow, and with it the size and running cost of the treatment system, as low as practical.
3. Treat with the right technology. Each technology has a range where it makes sense.
- Activated carbon adsorbs VOCs and odours. It suits lower concentrations and intermittent operation, and media replacement is the main running cost.
- Zeolite rotor concentrators take a large, dilute airflow and concentrate the VOCs into a much smaller stream. That makes final treatment smaller and cheaper to run.
- A regenerative thermal oxidiser (RTO) destroys VOCs at high temperature. Its ceramic beds recover much of the heat, which suits continuous, higher-concentration loads.
- Packed-bed, venturi and wet scrubbers remove acid gases, mists, fumes and soluble odours with a circulating liquid.
- Dust collectors remove particulate. Cartridge units suit fine dust from cement handling, grinding and welding. A baghouse suits high dust loads such as rice and feed milling. A cyclone takes out coarse material first.
4. Monitor and prove it. We add sensors and displays for the parameters that matter, such as TVOC, PM2.5, differential pressure across filters and fan status. These can feed AirSight so EHS and production see the same numbers.
The right treatment system is the one sized to your measured stream, not the largest one on the price list.
What’s included
A typical project covers the measurement and design study, capture hoods and ducting, fans, the treatment equipment, stacks, electrical and controls, monitoring, installation, commissioning and operator training. The scope table on this page shows how problems map to technologies. Indicative performance ranges for each technology are given on the air quality and emissions products page, and the real figure for your plant is confirmed against your measured stream.
We supply the AirMax air quality and environmental control range as technology partner and authorised distributor. Fans and blowers come from the matching duty, and replacement media from our filters and media range.
Clean and protected spaces
Some areas need clean air in, not dirty air out. Pharmaceutical filling, electronics assembly and some food packaging areas need controlled particle levels. We design HEPA filtration, laminar flow units, pass boxes and positive-pressure ventilation, so filtered air flows from clean areas towards less clean ones.
Before we design a clean space, we agree
- The cleanliness class or particle limit the process needs
- Which rooms sit at which pressure, and in what order
- Air change rate and filter positions
- How people and materials enter (gowning, pass boxes)
- How performance will be checked at handover and afterwards
How this fits with the rest of your plant
Emissions systems share power, controls and often plant-room space with compressed air and HVAC. Treatment fans add to the electrical load, and positive-pressure areas interact with the building’s cooling. Because we are responsible for every kind of air on the site, we plan those interfaces once. Compressed air for dust-collector pulse cleaning comes from the same compressed air system we design. Temperature and humidity in clean areas link to humidity control and HVAC and cooling.
The industries that most often need this work are printing and coating, chemicals, cement and building materials, agro-processing and pharmaceutical and healthcare.
Standards literacy
For a deeper explanation of technologies, filter classes and monitoring, read our industrial air quality guide.
