The problem: nobody can see the air
Ask most plants what a cubic metre of compressed air costs them and the answer is a guess. The compressors each have a controller, but the controllers do not talk to each other or to anyone else. Dryers alarm locally, if at all. Dew point is checked when something goes wrong. Air quality in production areas is measured once, for an audit, and then forgotten.
Without data, every decision is a debate. Is the new line why pressure is low, or is it leaks? Did last year’s upgrade actually save energy? Which compressor is due for service? Is the cleanroom holding its condition overnight? People argue from impressions because nobody has the numbers.
Our approach: an overlay, not a replacement
Nexus AirSight connects what you already have. It reads the compressors, dryers, meters and sensors on site, coordinates the compressors as one hall, and puts the results on one screen. The sample dashboard above shows the idea: machine tiles, flow, pressure, specific energy, dew point, alarms and trends. The figures in it are labelled sample data, and the toggle shows how a sequenced hall behaves differently from machines running on their own settings.
Machine logic stays at the machine. Each compressor keeps its own controller and every protection its manufacturer built in. AirSight adds sequencing, visibility and one energy number for the hall. It does not take away a single safety function.
Architecture, layer by layer
The scope table on this page sets out the five layers. In plain terms:
- Machine controllers keep each compressor, dryer and blower running safely.
- A sequencer decides which compressors run and in which order, holding the hall within one tight pressure band.
- A PLC and gateway collect signals from machines, power and flow meters and sensors, and convert between protocols.
- SCADA and a historian show live values, raise alarms and store history.
- The plant overlay turns that into dashboards and reports that owners, engineers and EHS can each use.
One hall. One pressure band. One energy number.
What AirSight does
Capabilities
- Real-time monitoring of every connected machine, meter and sensor
- Historical trends, so you can compare this week with last month, or before and after a change
- Alarm management, with priorities and acknowledgement, instead of a local buzzer nobody hears
- Reports and analytics, including specific energy (kWh/m³), unloaded hours and off-production demand
- Remote access, set up to your IT policy, for managers and engineers off site
For compressed air, the core values are flow, pressure at the compressor room and at key points of use, pressure dew point, power, running and loaded hours, and specific energy. Those are the same KPIs we use for energy optimisation, so savings stay visible after a project ends.
Air quality monitoring
AirSight is not limited to compressed air. The same platform can show conditions in production areas, cleanrooms, warehouses and around emissions treatment equipment.
| Parameter | Why it is monitored |
|---|---|
| PM2.5 and PM10 | Fine and coarse particulate in work areas and clean spaces |
| CO₂ | Ventilation adequacy in occupied spaces |
| TVOC | Solvent vapours from printing, coating and chemical processes |
| Temperature and humidity | Product storage, process conditions and worker comfort |
| Pressure and differential pressure | Room pressure cascades and filter loading |
| Air velocity | Laminar flow units, hoods and duct performance |
| Filter status | Change filters on condition, not on a calendar |
These sensors connect to the same PLC and SCADA layers, so production, engineering and EHS work from one set of numbers. See air quality and emissions and humidity control for the systems they watch over.
Protocols
AirSight speaks the protocols industrial equipment actually uses: Modbus (RTU and TCP), EtherNet/IP, PROFINET and hardwired digital and analogue I/O. Where a machine uses something else, a gateway converts it. We document every signal in an interface schedule so your team knows exactly what is connected and how.
Brownfield reality
Real compressor halls are mixed. Different brands, different ages, some machines with modern controllers and network ports, some with relay logic and a pressure switch. Some have communication options that were never fitted. Others were never designed to be connected at all.
That is why AirSight pairs naturally with plant renovation. Older machines with useful life stay on as peak or standby units, coordinated by the same sequencer as the new ones.
How this fits with products and services
AirSight sits on top of the compressed air system, whether we built it or not. New air compressors and air treatment can be specified with the communication options it needs. Design and engineering produces the control philosophy and interface schedule. Installation and commissioning includes logic and alarm testing before handover. An air audit is often the first step, because it shows which measurements matter most for your site.
