Phnom Penh, serving Cambodia and the region

Service

Planned maintenance that keeps air quality, uptime and energy where they were designed

An air compressor maintenance contract replaces breakdown repairs with planned care. Nexus Turnkey offers three tiers, Essential, Performance and Total Care, covering preventive maintenance to the manufacturer's schedule, genuine parts and consumables, diagnostics and reviews of operating data. Contracts cover compressors, dryers, filters and drains, and can extend to dehumidifiers, chillers, blowers and nitrogen generators. Inclusions and response terms are set out in your proposal, matched to how critical air is to your plant.

Two technicians servicing an electric motor

Why maintenance is a performance decision

A compressed air system starts to drift from its design the day it is commissioned. Filters load up and add pressure drop. Separators wear. Drains stick, open or closed. Coolers foul with dust. Each change is small. Together they raise energy use, reduce air quality and, eventually, stop a machine.

In Cambodia’s heat, humidity and dust, this happens faster. Coolers and intake filters clog sooner, and dryers work harder through the wet season.

Breakdown maintenance waits for the failure. Planned maintenance prevents most of them, and catches the rest early enough to fix them on your schedule rather than in the middle of a shift.

The cheapest repair is the one you scheduled.

What every contract includes

Whatever the tier, every annual maintenance contract (AMC) covers the same basics:

  • Preventive maintenance to the manufacturer’s schedule, by running hours and calendar, carried out by trained engineers.
  • Genuine parts and consumables. As an authorised distributor of Ingersoll Rand and Sollant, we use genuine service kits, filters, separators and lubricants for their machines.
  • The whole system, not just the compressor. Dryers, filters, condensate drains and oil-water separators are checked on every visit, because they decide your air quality.
  • A service record for every visit: what was checked, what was replaced, what was found and what we recommend.

Three tiers

InclusionEssentialPerformanceTotal Care
Scheduled preventive maintenance visitsIncludedIncludedIncluded
Service kits and consumables for scheduled visitsQuoted per visit To be confirmedIncluded To be confirmedIncluded
Dryer, filter and drain checksIncludedIncludedIncluded
Diagnostics (e.g. vibration, temperature, oil condition)Not includedIncluded To be confirmedIncluded
Operating-data review (hours, loading, pressure, energy)Not includedPeriodic To be confirmedRegular, using AirSight where installed To be confirmed
Leak surveyOptionalPeriodic To be confirmedPeriodic To be confirmed
Parts for breakdown repairsQuoted separatelyQuoted separatelyIncluded To be confirmed
Breakdown responseTo be confirmedTo be confirmedTo be confirmed
Performance and expansion adviceOn requestIncludedIncluded

Essential

For plants with capable in-house maintenance staff who want scheduled servicing done correctly, with genuine parts and a proper record. We handle the planned work. Your team handles daily checks.

Performance

Essential, plus diagnostics and reviews of operating data. We look for trends before they become failures: rising temperatures, changing load patterns, increasing pressure drop across filters, creeping unloaded power. Each review ends with recommendations, so the system’s efficiency is managed rather than assumed.

Total Care

For plants where compressed air is critical and the owner wants one party responsible for keeping it running. Total Care brings the widest scope of inclusions and the closest monitoring, and works best alongside AirSight, so we can see the system’s condition between visits.

What a service visit looks like

Each visit follows a checklist written for the equipment, not a general routine. The engineer reviews the controller’s alarm and event history, checks running and loaded hours, and carries out the scheduled tasks: filters, separators and lubricant as due, coolers inspected and cleaned, drains tested, drive belts checked where fitted, electrical connections inspected. Dryer dew point and pressure drop across filters are recorded. Before leaving, the engineer confirms the machine is back in its normal role in the sequence, and leaves a written record of what was found and what is recommended next.

Beyond compressors

Contracts can include the rest of your air systems: dehumidifiers, chillers and AHUs, blowers, nitrogen generators and air quality equipment. One contract and one service record make it easier to plan shutdowns and budgets, and give you one party to call.

How a contract starts

Starting a maintenance contract

  • Survey of each machine: model, serial number, running hours, condition
  • Review of service history and outstanding issues
  • Agreement of the equipment covered and the tier
  • A maintenance schedule built around your production calendar
  • First service visit, with a baseline record of condition

If a machine needs work before it can be brought under contract, we tell you at the survey, with the reasons.

Holding the gains

A maintenance contract is also how energy savings last. After an air audit or an energy optimisation project, regular data reviews show whether pressure, leakage and specific energy are holding, and catch drift early. Periodic leak detection stops new leaks undoing old work.

Parts outside a contract are available through our spare parts service. For a practical view of what an AMC should cover, read our compressor maintenance contract guide.

FAQ

Questions engineers ask us

What is an AMC?

An annual maintenance contract (AMC) is an agreement for planned maintenance over a year or longer. It sets out what will be serviced, how often, which parts and consumables are included, and how breakdowns are handled.

Which tier do we need?

It depends on how critical compressed air is to your production and how much maintenance your own team handles. Essential suits plants with capable in-house staff who want scheduled servicing done correctly. Performance adds diagnostics and data reviews. Total Care suits plants where air is critical and the owner wants one party responsible for keeping it running. We recommend a tier after seeing your equipment and operation.

Do you use genuine parts?

Yes. We are an authorised distributor of Ingersoll Rand and Sollant, and we use genuine parts and consumables for their machines. For other equipment, we use parts that meet the manufacturer's specification and tell you exactly what was fitted.

Can you maintain compressors of other brands?

Usually, yes. Many plants run mixed fleets. We survey each machine first, confirm parts availability and agree which machines the contract covers.

What are your response times for breakdowns?

Response terms are set out in your contract, matched to the tier and to your site's location and criticality. Ask us for the terms that would apply to your plant.

How much does a maintenance contract cost?

It depends on the equipment, running hours, tier and site. We price it after a survey of your installation, and the proposal shows exactly what is included.

Next step

Get a maintenance proposal for your equipment

List your compressors and air equipment, with models and running hours if you have them. We will survey the installation and recommend a tier.

Start typing to search