Phnom Penh, serving Cambodia and the region

Products · Nexus

Industrial blowers matched to the pressure, flow and duty of the process

An industrial blower moves large volumes of air at low pressure, and the right type depends on the pressure, the flow, how much that flow varies and how many hours it runs. Nexus Turnkey supplies the Nexus range of roots (rotary lobe), screw, high-speed turbo and side-channel blowers for aeration, pneumatic conveying, fermentation, aquaculture, combustion air and drying. Capacities are selected to your load, and we install, commission and maintain the blower system.

How to choose

Start from the duty, not the machine

Blower types compared qualitatively
TypeBest suited toStrengthsWatch for
Roots (rotary lobe)Conveying, aeration and general low-pressure dutySimple, rugged, tolerant of varying pressureNoise and pulsation; efficiency at higher pressure
Screw blowerContinuous duty at the upper end of blower pressuresInternal compression; often more efficient than roots at higher pressureHigher purchase cost
High-speed turbo (magnetic or air bearing)Large, continuous aeration with varying demandOil-free, quiet, efficient turndown within its rangeSurge limits; needs clean, cool intake air
Side-channel (regenerative)Small flows at low pressure or vacuumCompact, oil-free, few wearing partsLimited pressure and flow
Qualitative guidance. Final selection follows a site survey and your demand data.

Low-pressure air, without compressed-air costs

Many processes need a lot of air at low pressure: bubbling it through wastewater, carrying cement or flour along a pipe, agitating a fermenter, feeding a burner or drying a product. A blower is designed for exactly that duty. Using compressed air and throttling it down instead is one of the most expensive ways to make low-pressure air.

Nexus Turnkey supplies the Nexus range:

  • Roots blowers (rotary lobe), the rugged workhorse for conveying and aeration.
  • Screw blowers, with internal compression for continuous duty at higher blower pressures.
  • High-speed turbo blowers on magnetic or air bearings, oil-free, for large aeration duties.
  • Side-channel blowers (regenerative), compact units for small flows at low pressure or vacuum.

Capacities are selected to your load. Ask for a datasheet.

How to choose: duty point, variation and hours

Start with the duty: the flow you need, the pressure at the blower outlet, and how both vary. Then the running hours. A blower running continuously for years should be chosen on efficiency at its real duty points. A blower that runs a few hours a day can be chosen on simplicity and purchase cost.

The table above compares the types qualitatively. A roots blower moves a fixed volume per revolution and lets the system set the pressure; it is simple and forgiving. A screw blower compresses the air inside the machine before discharge, which often makes it more efficient at higher pressures. A turbo blower is a centrifugal machine running at high speed; it turns down efficiently within its range but has a surge limit. Side-channel blowers suit small flows. Our article on roots vs screw vs turbo blowers explains the trade-offs in more depth.

Control matters as much as the machine. Aeration blowers controlled from dissolved oxygen, and conveying blowers sized to the real line rather than a generous guess, use less energy for the same result.

What to consider in Cambodian plants

Intake air temperature affects how much air mass a blower delivers, and blower rooms in the hot season get hot. Ventilated, shaded blower rooms with cool intake air keep performance up. Dust from cement, flour, rice and feed handling must be kept out of intakes, and conveying systems need air that is dry enough not to cake the product. Turbo blowers, with their tight internal clearances and electronics, need particular attention to intake filtration and enclosure cooling.

Where blowers serve water and wastewater treatment, power matters as much as the machine. Aeration often runs around the clock, so the duty and standby arrangement, starting method and protection are reviewed against the site’s electrical supply, and the blower room is laid out so one unit can be serviced while the others run.

What Nexus supplies and supports

We define the duty, select the blower from the Nexus range, and design the package around it: silencers, relief and non-return valves, intake filtration, enclosures, controls and piping. We install, commission and verify performance at the duty point, then maintain the blower and supply parts. Savings are project-specific. We measure them against a baseline and verify them after implementation; we don’t promise a blanket percentage.

FAQ

Questions engineers ask us

Should I use a blower or a compressor?

If the process needs a large volume of air at low pressure, such as aeration or dilute-phase conveying, a blower is designed for it and uses far less energy than throttling compressed air down. Compressed air is the right choice where higher pressure is needed.

Roots, screw or turbo blower: which is most efficient?

It depends on the duty point and how much it varies. Screw and turbo blowers are often more efficient than roots at the same duty, especially at higher pressure or with continuous running. Roots blowers remain a simple, rugged choice for many conveying and smaller aeration duties. We compare them on your duty profile.

Why does aeration demand vary so much?

Biological treatment needs oxygen in proportion to the load arriving at the plant, which changes through the day. Controlling blowers from dissolved-oxygen readings, rather than running them flat out, matches air to demand.

What do blowers need for maintenance?

Intake filters, belts on belt-driven units, bearing lubrication on roots and screw blowers, and checks on silencers, relief valves and non-return valves. Turbo blowers with magnetic or air bearings have no oil to change but need clean intake air and periodic inspection.

Do you publish capacities for Nexus blowers?

Capacities are selected to your load. Ask for a datasheet.

Next step

Tell us what your blowers are feeding

Send the duty: what the air is for, the pressure and flow you think you need, and the running hours. We will propose a blower type and control approach.

Start typing to search